Arrow-plastic SA8662-A Manual do Utilizador

* Size rounded off to the nearest footBUILDING DIMENSIONSCAUTION: SOME PARTS HAVE SHARP EDGES. CAREMUST BE TAKEN WHEN HANDLING THE VARIOUS PIECESTO AV

It is important that the entire floor frame be anchored after the building is erected.Below are recommended ways of anchoring. Anchoring Down The Buil

11Remove from bag of screwsand save for the last step67293Weather Stripping (1)66029Plug (2)(Packed with Screws)66382Lower Door Guide (4)66183Roof Tri

Parts List P1212Assembly Part Part Quantity CheckKey No. Number Description in Carton List 1 6615 Rear Wall Angle 2 2 6617 Door Track Spl

13Assembly by Key No. B13

The front floor frame is made up ofthree pieces. The rear floor frame ismade up of two pieces. The holes inthese pieces will align when thepieces are

Step 2B1515● Parts Needed For ●Frame Assemblies●●●●● 6615 Rear Wall Angle (2)●●●●● 9924 Rear Wall Channel (2)The main frame pieces reinforce thewalls.

16Step 3B16● Parts Needed For ●Roof Beam Assembly●●●●● 8474 Roof Beam (1)●●●●● 8476 Side Wall Angle (1)The roof beams join the two gablesand support t

17NOTE:Door Track Splice (painted part)Step 4B17● Parts Needed For ●Door Track Assembly●●●●● 6617 Door Track Splice (1)●●●●● 9378 Door Track (2)The do

●●●●● Front Floor Assembly (1)●●●●● 8946 Side Floor Frame (2)●●●●● Rear Floor Assembly (1)● Parts Needed For ●Floor FrameStep 5B18The floor frame must

1 Position the rear corner panels atthe rear corners, as shown. The wid-est part of each rear corner panelmust be placed along the rear of thebuilding

2Owner's ManualBefore beginning construction, check local building codes regarding footings, locationand other requirements. Study and understand

● Parts Needed For ●FramesStep 7B2020●●●●● Door Track Assembly (1)●●●●● Rear Wall Angle Assembly (1)●●●●● 8476 Side Wall Angle (2)●●●●● Rear Wall

21●●●●● 6515 Wall Panel (4)●●●●● 6243 Wall Panel (2)● Parts Needed For ●Wall PanelsStep 8P21The wall panels come in two widths.Each wall panel has a

22● Parts Needed For ●Door JambStep 9P22●●●●● 9369 Door Jamb (2)The door jambs reinforce the dooropening and provide an attractivetrim. Follow these s

23The gables go on top of the front andrear walls to support the roof beams.NOTEThe gables are packed nestedtogether and might be mistakenas one piece

24Step 11B24● Parts Needed For ●Gables/Braces●●●●● Left Gable Assembly (2)●●●●● Right Gable Assembly (2)●●●●● 6658 Gable Brace (2)1 Lift and fasten a

25Step 12B25● Parts Needed For ●Roof Beams●●●●● Main Roof Beam (1)●●●●● 8474 Roof Beam (2)1 Fasten the main roof beam to thegable brace of the front g

26Step 13B26● Parts Needed For ●Right Roof Panel●●●●● 8466 Right Roof Panel (1)Installing the roof panels is best donewith a step ladder. Begin insta

1 Install a left roof panel at the leftrear and right front corner of the roof.Install a right roof panel at the leftfront corner of the roof.3 Insta

28Step 15B28● Parts Needed For ●Ridge Cap●●●●● 8461 Ridge Cap (1)1 Install the ridge cap on the com-pleted roof section using bolts andnuts. Do not fa

29Step 16B29● Parts Needed For ●Roof Trim●●●●● 8482 Side Roof Trim (2)1 Attach the side roof trim to thelower end of the roof panels on eachside of th

3Selecting and Preparing Your Site: Before assembly, you will want to decide ona location for your building. The best location is a level area with go

30END VIEWSHOWING:Step 17P30● Parts Needed For ●Door Assembly●●●●● 10478 Right and Left Doors (2)●●●●● 10498 Horizontal Door Brace (4)●●●●● 6278

31Step 18P31● Parts Needed For ●Door Installation & Adjustment●●●●● Right Door Assembly (1)●●●●● Left Door Assembly (1)1 From inside the building,

SOME FACTS ABOUT RUSTRusting is a natural oxidizing process that occurswhen bare metal is exposed to moisture. Problemareas include screw holes, unfin

4Safety precautions are important to follow throughout the construction of your building.•Care must be taken when handling variouspieces of your build

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immedia

ACCESSORIES... A6 WEB6* Some drilling required to fit buildings without mid-wall bracing.Model No. SS404• Makes 8" to 12" (20-30cm)

THIS PAGEWA SLEFTBLANKINTENTIONALLY7

THIS PAGEWA SLEFTBLANKINTENTIONALLY8

The Foundation For Your Building9FRONT(DOOR)FRONT(DOOR)Foundation B09Note: Finished Slab dimensions, with lumber removed.OPTION 1: ARROW FLOOR FRAM